RSA603 & RSA607 Real Time Spectrum Analyzers

    • USB spektrální analyzátor
    • 9 kHz až 3 GHz nebo 9 kHz-7,5 GHz
    • 40 MHz real-time bandwidth
    • v dodávce základní verze SignalVu software
    • záruka: 3 roky
    TEKTRONIX
    Další parametry
    Cena na dotaz
    Kat. č: RSA603RSA607.w
    dostupnost na dotaz

    Výběru neodpovídá žádná položka.

    Parametry a specifikace

    Frequency range
    RSA 603A 9 kHz to 3 GHz
    RSA 607A 9 kHz to 7.5 GHz
    Frequency marker readout accuracy

    ±(RE × MF + 0.001 × Span) Hz

    RE: Reference Frequency Error

    MF: Marker Frequency [Hz]

    Reference frequency accuracy
    Initial accuracy at Cal (30 min warm-up) ±1 x 10-6
    First year aging, typical ±1 x 10-6 (1 year)
    Cumulative error (Initial accuracy + temperature + aging), typical 3 x 10-6 (1 year)
    Temperature drift ±0.9 x 10-6 (-10 to 60 °C)
    External reference input BNC connector, 50 Ω nominal
    External reference input frequency

    Every 1 MHz from 1 to 20 MHz plus the following: 1.2288 MHz, 2.048 MHz, 2.4576 MHz, 4.8 MHz, 4.9152 MHz, 9.8304 MHz, 13 MHz, and 19.6608 MHz.

    The spurious level on the input signal must be less than -80 dBc within 100 kHz offset to avoid on-screen spurious.

    External reference input range ± 5 ppm
    External reference input level -10 to +10 dBm
    GNSS
    Accuracy, when locked to GNSS1 ±0.025 ppm2
    GNSS Trained Accuracy, when GNSS antenna is disconnected3, 4

    ±0.025 ppm5

    ±0.08 ppm6

    RF input
    RF Input Impedance 50 Ω
    RF VSWR (RF Attn = 20 dB), typical

    < 1.2 (10 MHz to 3 GHz)

    < 1.5 (>3 GHz to 7.5 GHz)

    RF VSWR preamp ON, typical

    < 1.5 (10 MHz to 6 GHz, RF ATT=10 dB, preamp on)

    < 1.7 (> 6 GHz to 7.5 GHz, RF ATT=10 dB, preamp on)

    Maximum RF input level
    Maximum DC voltage ±40 V (RF input)
    Maximum safe input power

    +33 dBm (RF input, 10 MHz to 7.5 GHz, RF Attn ≥ 20 dB)

    +13 dBm (RF input, 9 kHz to 10 MHz)

    +20 dBm (RF input, RF Attn < 20 dB)

    Maximum safe input power (Preamp On)

    +33 dBm (RF input, 10 MHz to 7.5 GHz, RF Attn ≥ 20 dB)

    +13 dBm (RF input, 9 kHz to 10 MHz)

    Maximum measurable input power

    +30 dBm (RF input, ≥10 MHz to Fmax, RF ATT Auto)

    +20 dBm (RF input, <10 MHz, RF ATT Auto)

    Input RF attenuator 0 dB to 51 dB (1 dB step)
    Amplitude and RF flatness
    Reference level setting range -170 dBm to +40 dBm, 0.1 dB step, (Standard RF input)

    1Tested using GPS system.

    2For use to a stability of ±0.025ppm, the unit should be powered on continuously for 2 to 5 days after initial unpacking.

    3Tested using GPS system.

    4For 24 hours continuous operation within temperature limits (see footnotes 5 and 6) after GNSS training. Refer to cumulative error specification if operating in GNSS trained mode beyond 24 hours since last training.

    5For less than 3 °C ambient temperature change after training.

    6For less than 10 °C ambient temperature change after training.

    Soubory ke stažení a odkazy

    Potřebujete poradit?

    Zavolejte nám na +420 325 610 123 a vyžádejte si specialistu v tomto oboru.